Self Adhesive hangers SC
|
 |
|
- Self-adhesive hangers are designed to fix efficiently insulation on smooth surfaces such as air ducts, attenuators, chambers and enclosures.
- It consists of a pin, firmly mounted on a high-quality self-adhesive base.
- Locking washers supplied in each box.
 |
Technical specifications
|
 |
|
| Base |
|
Material |
Galvanized steel |
| |
|
Dimensions (A x B) |
50 x 50 mm (2" x 2") |
| |
|
Thickness |
0.4 mm (28 ga.) |
| Shank |
|
Material |
≤ 63 mm (2-1/2’’) => galvanized steel |
| |
|
|
≥ 76 mm (3’’) => copper plated steel |
| |
|
Diameter |
2,7 mm (12 ga.) |
| |
|
Lengths |
19 to 400 mm (3/4” to 16”) |
| |
|
|
|
|
| |
|
|
 |
|
| Adhesive |
|
Base |
White, cross-linked, closed-cell polyethylene foam |
| |
|
Coating |
Modified acrylate adhesive on both sides |
| |
|
Liner |
Siliconized paper |
| |
|
Thickness |
1 mm (1/25”) |
| Power (FINAT-TM 1, on stainless steel, one side covered with 50 microns polyester film) |
| |
|
1 minute |
1 minute |
| |
|
20 minutes |
tear |
| |
|
24 hours |
tear |
| Shear strength (FINAT-TM 8, on stainless steel, one side covered with 50 microns polyester film) |
| |
|
23 °C |
>150 hours |
| |
|
70 °C |
1 hour |
| |
|
|
|
|
| |
|
|
 |
|
| Locking washer: CL 2 - 30 |
|
Material |
Galvanized spring steel |
| |
|
Diameter |
30 mm (1-3/16”) - 38 mm (1-1/2”) on request |
| |
|
Thickness |
0,35 mm (28 ga.) |
| |
|
Edges |
Bevelled |
| |
|
|
|
|
| |
|
|
Application recommendation
|
| Quantity |
|
8 to 12 hangers per square meter (1,20 sq Yd) are required in standard condition. |
| Application |
|
* Surfaces should be clean and dry, free of dust, grease, oil and any other loose matter. |
| |
|
* Avoid using degreasing - products |
| |
|
* Not for use in application likely to make contact with chlorinated, cetonic or ether solvents |
| Application temperature |
|
+15 °C to +25 °C (+60°F to +80°F) |
| Holding temperature |
|
-40 °C to +80 °C (-40°F to +180°F) |
|
| |
Storage
|
|
|
| 2 years when stored in a dry place. +10 °C to +30 °C (+50°F to +90°F), with 50% relative humidity. |
| |
|
|
Application
|
|
|
 |
|
Apply at temperature range +15ºC to +25ºC (+60ºF to +89ºF). Surfaces should be clean and dry, free of dust, grease, oil and any other loose matter. Do not use degreasing products. Not for use in application likely to make contact with chlorinated, cetonic or esther solvents. |
| |
|
|
 |
|
Place the hanger in the required position and press the base against the surface to be insulated. |
| |
|
|
 |
|
Remove the protective release paper taking care not to touch the adhesive. |
| |
|
|
 |
|
Insulation can be impaled immediately and firmly locked with locking washers, but maximum strength of adherence is achieved after 24 hours. If necesaary, cover the pin with protective cap. |
| |
|
|
 |
|
|
